Load video: ISO-Lateral Shoulder Press DRE8004

Exercises and muscles targeted

Exercise	Muscles Targeted
ISO-Lateral Shoulder Press — Standard Grip	Anterior Deltoid (primary), Lateral Deltoid (primary — overhead press path recruits all three deltoid heads), Triceps Brachii (secondary — elbow extension at lockout), Upper Trapezius (secondary — scapular elevation at top), Serratus Anterior (upward scapular rotation)
ISO-Lateral Shoulder Press — Hammer Grip	Anterior Deltoid (primary — hammer grip positions the forearm to increase anterior deltoid emphasis), Triceps Brachii (secondary — reduced elbow flare reduces triceps involvement vs standard grip), Upper Trapezius (secondary), Lateral Deltoid (reduced secondary compared to standard grip)
Unilateral ISO Shoulder Press (single arm)	Anterior Deltoid (unilateral, primary), Lateral Deltoid (primary), Core (anti-rotation stabiliser under asymmetric overhead load), Upper Trapezius (secondary), Rotator Cuff — Supraspinatus, Infraspinatus (stabilisers — increased unilateral demand)
ISO Shoulder Press — Isometric Hold (lockout)	Anterior and Lateral Deltoid (sustained isometric at full overhead extension), Triceps Brachii (isometric at lockout), Upper Trapezius, Serratus Anterior (sustained scapular upward rotation), Rotator Cuff (sustained joint stabilisation throughout hold)
ISO Shoulder Press — Slow Eccentric	Anterior and Lateral Deltoid (eccentric loading through the full descending arc — maximum hypertrophy stimulus), Triceps Brachii (eccentric), each arm descends on its own independent path without being stopped by the opposite arm's position
Alternating ISO Shoulder Press	Anterior and Lateral Deltoid (alternating per rep — each arm drives independently through full convergence arc), Core (increased anti-rotation demand per alternating press), Rotator Cuff (dynamic stabiliser per alternating overhead load)

The DRE8004 trains the deltoids through an overhead pressing path that converges inward as the arms extend, replicating the natural shoulder joint trajectory more closely than a fixed bilateral bar. The standard grip recruits all three deltoid heads through the full press path. The hammer grip narrows the emphasis toward the anterior deltoid by positioning the forearm in the neutral wrist orientation that reduces lateral deltoid and triceps contribution while maintaining a mechanically sound shoulder position. The Dynasty Flex-Stack System's 1:1 felt weight ratio means both grip options deliver accurate, consistent resistance through the full overhead arc in both the concentric and eccentric phases.

Who this machine is built for

Serious Home Gym Builders
You press horizontally on the DRE8001 and you want overhead pressing covered with the same ISO-lateral independent arm quality on a dedicated shoulder station. The DRE8004 delivers both standard overhead pressing and hammer grip anterior deltoid pressing from a single 66"×57" station with a 210 lb stack and the Dynasty Flex-Stack System's 1:1 felt weight ratio. The pneumatic single-hand seat and 5-position backrest handle any user proportions without manual wrestling between sets.

Bodybuilders and Physique Athletes
Lateral deltoid width and anterior deltoid thickness are both visual priorities in every physique category, and the DRE8004 trains them through an ISO-lateral overhead press where each arm follows the shoulder's natural convergence trajectory independently. The standard grip covers full deltoid pressing for size and width. The hammer grip shifts toward anterior deltoid isolation with reduced triceps involvement for sessions where front delt hypertrophy is the specific goal. The 2.5kg micro-increment plates allow load progression to be managed at the granularity that shoulder pressing demands — the shoulder responds poorly to large stack jumps that force technique breakdown.

Commercial Gym Owners and Operators
The pneumatic rack-and-pinion seat holds position under load without the pin slipping that standard hole-and-pin seats develop over time in high-use commercial environments. At 578 lbs and a 66"×57" footprint the DRE8004 anchors firmly in the commercial floor plan. The single-hand operation on all adjustments and the transport wheels allow quick repositioning and fast user transitions. The 5kg base weight and 2.5kg micro-increment plates mean the machine serves the full range of the commercial membership from beginners to advanced lifters on the same station.

Powerlifters and Strength Athletes
Overhead pressing accessory volume on the DRE8004 develops anterior and lateral deltoid strength that supports the lockout position of the competition bench press and the overhead bracing demand of the squat. The ISO-lateral independent arms reveal left-right shoulder pressing asymmetries that a barbell overhead press masks, and unilateral pressing on the DRE8004 addresses these independently. The 1:1 felt weight ratio makes the accessory load tracking straightforward alongside competition training programming.

Private Personal Training Studios
Two pressing handle options from one machine give trainers the ability to shift between full deltoid overhead pressing and anterior deltoid hammer grip focus within the same session without additional equipment. The single-hand seat adjustment and five backrest positions fit any client height in seconds, and the zero-movement rack-and-pinion seat provides the stable base that overhead pressing requires when clients are working at heavier loads under close coaching supervision.

Physical Therapists and Sports Medicine Practitioners
The hammer grip position reduces the shoulder stress of overhead pressing by positioning the forearm in the neutral wrist orientation that decreases impingement risk relative to a pronated overhead grip in some shoulder conditions. The ISO-lateral independent arms allow one shoulder to be trained through a different range of motion or at a different load than the other during asymmetric rehabilitation. The 5-position backrest and pneumatic seat allow the torso support angle to be precisely set for each patient's mobility level and condition. Exercise selection, load, and range of motion must always follow the clinical programme specific to each patient's condition and recovery stage.

How to setup and use

Setting Up the DRE8004 ISO-Lateral Shoulder Press

Select the working weight on the stack using the selector pin. The Dynasty Flex-Stack System delivers a 1:1 felt weight ratio — each arm feels half the selected stack weight. Account for this when setting the starting load for the first session, and start conservatively to establish the correct pressing path before increasing weight.
Adjust the seat height using the pneumatic lever with a single hand. The correct seat position places the handles at approximately shoulder height when sitting with the back against the backrest — the forearms should be close to horizontal at the starting position. The rack-and-pinion system locks the seat with zero movement under the overhead pressing load.
Set the backrest to one of five positions. A more upright backrest provides greater upper back support during heavy pressing. A slightly reclined position allows the pressing arc to extend higher overhead. Choose the position where the lower and mid-back feel fully supported throughout the press.
Choose the handle type for the session: the standard grip (36×28×460mm) for full deltoid overhead pressing, or the hammer grip (28×36×130mm) for anterior deltoid emphasis with reduced shoulder stress.
Sit on the seat pad with the back fully against the backrest and the head against the head pad. Grip the selected handles firmly and confirm the starting position feels balanced — both arms loaded at the starting position and the back stable against the pad.
Confirm the starting handle height is correct before beginning. If the handles start below shoulder level, raise the seat one position. If above, lower it one position.

Performing the Exercise

From the starting position with both arms loaded at shoulder height and the elbows pointing outward, press both arms upward simultaneously, following the natural convergence path of each arm as they move inward toward the centre line of the body at the top of the press.
Focus the drive on the deltoids pushing the handles upward through the full overhead arc rather than primarily straightening the elbows. The triceps contribute at lockout but should not be the primary driver through the mid-range.
Drive to full arm extension at the top where both arms are extended overhead and the deltoids are at peak contraction, holding for one to two seconds before beginning the return.
Lower both arms under control over at least two seconds, allowing the deltoids to work through the full eccentric return. Each arm descends on its own independent convergence path.
For hammer grip sets, confirm the wrists stay neutral — neither pronated nor supinated — throughout the press. The hammer grip position is specifically designed to keep the wrist in this neutral orientation through the full overhead arc to reduce shoulder stress.
For unilateral sets, press one arm at a time while the other holds its starting position. The independent arm design allows full single-arm pressing without any mechanical interference from the opposite arm. Reduce the stack weight significantly from bilateral working loads for unilateral sets.

Owner's Manual

Access the complete assembly guide, parts list, and maintenance schedule below.

Download Owners Manual

Shipping & Delivery

All Dynasty Fitness equipment ships free across the 48 contiguous US states via freight carrier. If the product description says preorder, we'll send you an estimated delivery date via email.

Estimated delivery: 7–14 business days from order confirmation. You will receive a tracking number and a delivery window confirmation call before your shipment arrives. Deliveries are curbside standard, white glove delivery to room of choice is available at checkout.

Returns: Free within 30 days of delivery. Items must be in original condition and packaging. Refunds processed within 5 business days of return receipt.

Questions? Contact our team at:
📧Email: info@thedynastyfitness.com
📞Call: +1 (213)-584-0858

Need a buying guide?

Looking for one to one support before making final decision?
Feel free to contact us. Our expert support team would love to assist you.

Need Installation Help?

We have partnered with another company to help provide installation around the country. Please use the link below to see the price per machine for installation
See Installation Rates

Payment & Security

Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.

Save 10%

ISO-Lateral Shoulder Press DRE8004

$2,649.00

$2,649.00 ~~$2,949.00~~ 10% off (Save$300.00 )

Commercial Grade
Pay With HFA/FSA

Free Shipping

Weight Stack: 210lb

210lb 250lb

The Dynasty Fitness DRE8004 ISO-Lateral Shoulder Press is a selectorized overhead press machine with independent converging arms that simulate the shoulder joint's natural pressing trajectory, so each deltoid drives through its own movement path without the bilateral compensation that a fixed bar forces when one shoulder is stronger than the other. A multi-handle design provides two distinct pressing positions from the same station: standard overhead grips for full deltoid pressing through the complete overhead arc, and a hammer grip position that specifically targets the anterior deltoid with reduced shoulder stress by changing the wrist and elbow angle through the press — making it the more accessible option for users with shoulder sensitivity or those prioritising front deltoid development with less lateral involvement.

A 5-position backrest combined with a pneumatic rack-and-pinion seat that holds position under load with zero movement provides stable, precise support for the full overhead press range, and all adjustments operate single-handed. The Dynasty Flex-Stack System delivers a true 1:1 felt weight ratio with a 5kg base and 2.5kg micro-increment plates for precise progressive loading. Built to commercial grade at 66"×57"×63" with a 210 lb standard stack and a 250 lb upgrade option available through Dynasty Fitness, the DRE8004 is built for commercial gyms, personal training studios, and serious home gym setups where ISO-lateral shoulder pressing with biomechanically specific grip options is a deltoid programming priority.

ISO-lateral independent converging arms follow the shoulder joint's natural pressing trajectory so each deltoid works through its own full range of motion and reaches its own peak contraction without the stronger arm compensating for the weaker one across any rep
Dual-handle design offers standard overhead grips for complete deltoid pressing and a hammer grip position that specifically targets the anterior deltoid with reduced shoulder stress — two distinct biomechanical functions from the same station rather than two ways to hold the same press
Pneumatic rack-and-pinion seat holds position under load with zero movement during heavy overhead pressing, combined with a 5-position backrest and single-hand operation on all adjustments so setup between users and between sets stays fast and stable
Dynasty Flex-Stack System delivers a true 1:1 felt weight ratio with 2.5kg micro-increment plates starting at a 5kg base, giving shoulder pressing the fine-tuning granularity that overhead movements require when progressing in smaller steps than compound pushing exercises

Limited time offer

Get 20% off when you order 4 or more pieces of equipment!

Exercises and muscles targeted

Exercise	Muscles Targeted
ISO-Lateral Shoulder Press — Standard Grip	Anterior Deltoid (primary), Lateral Deltoid (primary — overhead press path recruits all three deltoid heads), Triceps Brachii (secondary — elbow extension at lockout), Upper Trapezius (secondary — scapular elevation at top), Serratus Anterior (upward scapular rotation)
ISO-Lateral Shoulder Press — Hammer Grip	Anterior Deltoid (primary — hammer grip positions the forearm to increase anterior deltoid emphasis), Triceps Brachii (secondary — reduced elbow flare reduces triceps involvement vs standard grip), Upper Trapezius (secondary), Lateral Deltoid (reduced secondary compared to standard grip)
Unilateral ISO Shoulder Press (single arm)	Anterior Deltoid (unilateral, primary), Lateral Deltoid (primary), Core (anti-rotation stabiliser under asymmetric overhead load), Upper Trapezius (secondary), Rotator Cuff — Supraspinatus, Infraspinatus (stabilisers — increased unilateral demand)
ISO Shoulder Press — Isometric Hold (lockout)	Anterior and Lateral Deltoid (sustained isometric at full overhead extension), Triceps Brachii (isometric at lockout), Upper Trapezius, Serratus Anterior (sustained scapular upward rotation), Rotator Cuff (sustained joint stabilisation throughout hold)
ISO Shoulder Press — Slow Eccentric	Anterior and Lateral Deltoid (eccentric loading through the full descending arc — maximum hypertrophy stimulus), Triceps Brachii (eccentric), each arm descends on its own independent path without being stopped by the opposite arm's position
Alternating ISO Shoulder Press	Anterior and Lateral Deltoid (alternating per rep — each arm drives independently through full convergence arc), Core (increased anti-rotation demand per alternating press), Rotator Cuff (dynamic stabiliser per alternating overhead load)

Who this machine is built for

How to setup and use

Setting Up the DRE8004 ISO-Lateral Shoulder Press

Select the working weight on the stack using the selector pin. The Dynasty Flex-Stack System delivers a 1:1 felt weight ratio — each arm feels half the selected stack weight. Account for this when setting the starting load for the first session, and start conservatively to establish the correct pressing path before increasing weight.
Adjust the seat height using the pneumatic lever with a single hand. The correct seat position places the handles at approximately shoulder height when sitting with the back against the backrest — the forearms should be close to horizontal at the starting position. The rack-and-pinion system locks the seat with zero movement under the overhead pressing load.
Set the backrest to one of five positions. A more upright backrest provides greater upper back support during heavy pressing. A slightly reclined position allows the pressing arc to extend higher overhead. Choose the position where the lower and mid-back feel fully supported throughout the press.
Choose the handle type for the session: the standard grip (36×28×460mm) for full deltoid overhead pressing, or the hammer grip (28×36×130mm) for anterior deltoid emphasis with reduced shoulder stress.
Sit on the seat pad with the back fully against the backrest and the head against the head pad. Grip the selected handles firmly and confirm the starting position feels balanced — both arms loaded at the starting position and the back stable against the pad.
Confirm the starting handle height is correct before beginning. If the handles start below shoulder level, raise the seat one position. If above, lower it one position.

Performing the Exercise

From the starting position with both arms loaded at shoulder height and the elbows pointing outward, press both arms upward simultaneously, following the natural convergence path of each arm as they move inward toward the centre line of the body at the top of the press.
Focus the drive on the deltoids pushing the handles upward through the full overhead arc rather than primarily straightening the elbows. The triceps contribute at lockout but should not be the primary driver through the mid-range.
Drive to full arm extension at the top where both arms are extended overhead and the deltoids are at peak contraction, holding for one to two seconds before beginning the return.
Lower both arms under control over at least two seconds, allowing the deltoids to work through the full eccentric return. Each arm descends on its own independent convergence path.
For hammer grip sets, confirm the wrists stay neutral — neither pronated nor supinated — throughout the press. The hammer grip position is specifically designed to keep the wrist in this neutral orientation through the full overhead arc to reduce shoulder stress.
For unilateral sets, press one arm at a time while the other holds its starting position. The independent arm design allows full single-arm pressing without any mechanical interference from the opposite arm. Reduce the stack weight significantly from bilateral working loads for unilateral sets.

Owner's Manual

Access the complete assembly guide, parts list, and maintenance schedule below.

Download Owners Manual

Shipping & Delivery

All Dynasty Fitness equipment ships free across the 48 contiguous US states via freight carrier. If the product description says preorder, we'll send you an estimated delivery date via email.

Returns: Free within 30 days of delivery. Items must be in original condition and packaging. Refunds processed within 5 business days of return receipt.

Questions? Contact our team at:
📧Email: info@thedynastyfitness.com
📞Call: +1 (213)-584-0858

Need a buying guide?

Looking for one to one support before making final decision?
Feel free to contact us. Our expert support team would love to assist you.

Need Installation Help?

We have partnered with another company to help provide installation around the country. Please use the link below to see the price per machine for installation
See Installation Rates

Payment & Security

Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.

ISO-Lateral Shoulder Press DRE8004

$2,649.00

$2,649.00 ~~$2,949.00~~ 10% off (Save$300.00 )

Key Features

ISO-Lateral Independent Converging Arms

Left and right arm frames move independently on converging pressing paths that simulate the natural trajectory of the shoulder joint during overhead pressing. The shoulder's glenohumeral joint does not press straight upward in a vertical line — it follows a slightly inward arc as the arm rises overhead, which is why a fixed bilateral press bar requires the shoulder to compromise its natural path to accommodate both arms moving on the same fixed axis. The independent convergence path on the DRE8004 allows each arm to follow the correct trajectory independently, which maintains shoulder joint alignment through the full press and allows each deltoid to reach its peak contraction at the top without being mechanically limited by the opposite arm.

Hammer Grip Handle Position

The shorter hammer grip handles (28×36×130mm) position the forearms in a neutral wrist orientation during the overhead press rather than the pronated position of a standard overhead grip. The neutral forearm position reduces the internal shoulder rotation that occurs during a pronated overhead press, which is the rotation that narrows the subacromial space and creates impingement risk under heavy loading. The hammer grip also shifts the press emphasis toward the anterior deltoid by changing the angle at which the deltoid fibres are recruited, making it the grip choice for anterior deltoid isolation work and for users who experience shoulder discomfort during standard overhead pressing.

Standard Overhead Grip

The longer standard grips (36×28×460mm) provide the full overhead press handle for complete deltoid engagement through the entire pressing arc. The greater grip length accommodates different shoulder widths and allows a stable hand position through the overhead arc without the forearm reaching an awkward angle at the top. The standard grip recruits all three deltoid heads — anterior, lateral, and posterior — through the press path, making it the primary grip for overall shoulder development and pressing strength across the full deltoid.

Pneumatic Rack-and-Pinion Seat

The seat adjusts through a pneumatic-assisted rack-and-pinion mechanism, combining the ease of a gas spring adjustment with the positional rigidity of a toothed rack system. The pneumatic assist allows one-hand height changes with minimal force between sets. The rack-and-pinion engagement locks the seat at the selected height with zero movement under the overhead pressing load — which is the load direction that places the most vertical force on the seat structure during the press. A seat that shifts under load during overhead pressing changes the starting height mid-set, which disrupts the pressing arc and requires the user to compensate rather than focus on the deltoid contraction.

Dynasty Flex-Stack System

The DRE8004 runs on the Dynasty Flex-Stack System, delivering a true 1:1 felt weight ratio through the full overhead press arc. The 5kg base weight combined with two 2.5kg micro-increment plates allows the working load to be adjusted in 2.5kg steps rather than the 5kg minimum increments that standard selectorized machines provide. Shoulder pressing is among the exercises where 5kg jumps are frequently too large to maintain clean technique, particularly in the mid-range of a training programme where strength increases are gradual. The 2.5kg increment allows progression at the rate the shoulder is actually developing strength rather than forcing jumps that compromise the press.

Clump Weights and Elastic Latch Assembly

Two clump weights are attached to each arm frame to counterbalance the mechanical weight of the arms themselves, ensuring the resistance felt through the handles comes from the stack rather than from the mechanical weight of the unloaded arm frames. The elastic latch assembly manages the arm mechanism at the starting position, keeping the arms in the loaded starting position without requiring the user to hold against the weight of the unloaded arm structure when getting into position. Both components contribute to the clean, resistance-accurate feel of the machine that makes the Dynasty Flex-Stack 1:1 ratio possible.

Product Information
Product Name	ISO-Lateral Shoulder Press
Model	DRE8004
Series	DRE80 Selectorized Series
Product Type	Selectorized ISO-Lateral Shoulder Press Machine
Function	ISO-lateral independent converging overhead press — bilateral and unilateral
Target Muscles	Anterior Deltoid, Lateral Deltoid (primary), Triceps Brachii, Upper Trapezius (secondary)
Resistance System	Dynasty Flex-Stack System — 1:1 felt weight ratio
Grade	Commercial
Colour	Black
Dimensions and Weight
Length	66 in (167.5 cm)
Width	57 in (144.4 cm)
Height	63 in (160.2 cm)
Net Weight	578 lbs (262 kg)
Weight Stack
Standard Weight Stack	210 lbs
Upgraded Weight Stack	250 lbs — contact Dynasty Fitness
Base Weight	5 kg
Micro-Increment Plates	2.5 kg x2
Arms and Handles
Arm Design	ISO-lateral independent — left and right arm frames on separate converging paths
Standard Overhead Grips	36×28×460mm x2 — full deltoid overhead press
Hammer Grips	28×36×130mm x2 — anterior deltoid emphasis, reduced shoulder stress
Arm Counterweights	Clump weights x2 per arm — balances mechanical arm weight for 1:1 felt ratio accuracy
Seat and Adjustability
Seat Adjustment	Pneumatic rack-and-pinion — single-hand, zero movement under load
Backrest Positions	5 positions
Adjustment Operation	All adjustments single-hand operable
Transport Wheels	3 x built-in rolling wheels
Mechanism and Bearings
Pulleys	4.5" pulley x4, 3.5" pulley x1, V-pulley x1
Bearings	6205 x4, Joint Bearing M12 x2
Frame and Construction
Main Frame Tubing	1.97"×5.9"×0.1" rectangular steel
Movement Arm Tubing	Φ2.4"×0.1"
Indoor Use Only	Yes

Q: What does the hammer grip position change compared to the standard overhead grip?
A: The hammer grip positions the forearms in a neutral wrist orientation throughout the overhead press rather than the pronated position of a standard grip. The neutral forearm reduces the internal shoulder rotation that occurs with a pronated grip, which narrows the subacromial space and creates the impingement risk that makes heavy overhead pressing uncomfortable for some users. The hammer grip also shifts the deltoid emphasis toward the anterior head by changing the elbow angle relative to the torso, which reduces lateral deltoid and triceps co-activation and concentrates more of the pressing stimulus on the front of the shoulder. Use the hammer grip for anterior deltoid isolation sessions or whenever the standard grip creates shoulder discomfort.

Q: How is the ISO-lateral convergence path different from a standard overhead press machine?
A: On a standard overhead press machine, both arms are mechanically linked to a single bar or connected mechanism that forces them to move at the same rate and through the same fixed arc. The DRE8004's ISO-lateral arms move independently on convergence paths — each arm follows a slightly inward arc toward the centre as it presses overhead, which matches the natural shoulder joint trajectory more closely than a fixed bilateral bar. This also means neither arm can receive assistance from the other, making every rep a true bilateral measurement of each side's pressing strength independently.

Q: Why does the seat need to hold position with zero movement during shoulder pressing?
A: The overhead press creates significant downward force through the seat as the deltoids drive upward — the body presses against the seat to generate the reaction force that allows the arms to press upward. A seat that shifts under this load changes the starting position mid-set, which alters the pressing arc and forces the user to compensate their technique to re-establish the correct arm angle relative to the handle height. The rack-and-pinion locking mechanism on the DRE8004 engages the seat at the selected height with a toothed precision lock that holds its position regardless of the pressing force applied throughout the set.

Q: What is the Dynasty Flex-Stack System and why do the 2.5kg micro-increment plates matter for shoulder training?
A: The Dynasty Flex-Stack System is the internal pulley arrangement that delivers a true 1:1 felt weight ratio between the stack selection and the resistance felt during the overhead press. The 5kg base weight combined with two 2.5kg micro-increment plates allows the working load to be increased or decreased in 2.5kg steps. Shoulder pressing strength increases more gradually than compound pushing movements like the chest press, and 5kg stack jumps are frequently too large to maintain clean technique across consecutive sessions. The 2.5kg increments match the load to the actual rate of deltoid strength development.

Q: Can I press one arm at a time on the DRE8004?
A: Yes. The independent arm frames allow either arm to be pressed solo while the other stays at the starting position or is held statically. Unilateral ISO-lateral shoulder pressing identifies and addresses left-right deltoid strength asymmetries that bilateral pressing masks. It also increases the rotational core stabilisation demand as the body resists twisting toward the pressing side. Reduce the stack weight significantly from bilateral working loads for unilateral sets — one arm pressing against half the bilateral stack is a substantially different stimulus than the full single-arm load.

Q: What Dynasty Fitness machines pair with the DRE8004 for a complete shoulder and upper body training area?
A: The DRE8004 covers ISO-lateral overhead pressing for anterior and lateral deltoid development. Pair it with the Pectoral Fly/Rear Deltoid DRE8003 to add posterior deltoid training through the reverse fly, covering all three deltoid heads across both machines. The ISO-Lateral Chest Press DRE8001 adds horizontal pressing for pectoral and anterior deltoid volume below the overhead plane. The Adjustable Seated Cable Row DRE8005 provides horizontal pulling for the lats and mid-back to balance the push volume. Together these four machines cover the complete upper body push-pull training area from dedicated ISO-lateral and cable selectorized stations.

Commercial Selectorized Machines. Engineered to Perform.

Dynasty Resistance Elite

The Dynasty Resistance Elite is Dynasty Fitness's flagship selectorized series, built around the Dynasty Flex-Stack System that delivers a true 1:1 felt weight ratio across the majority of the lineup. What you select on the stack is exactly what you lift, giving every session accurate, progressive resistance from the first rep to the last.

The series covers the complete commercial training floor. ISO-lateral pressing and pulling machines including the ISO-Lateral Chest Press, ISO-Lateral Shoulder Press, and ISO-Lateral Seated Row train each side of the body independently through its own natural arc, eliminating the compensation that fixed bilateral machines allow. Dedicated lower body stations including the Leg Press/Hack Squat, Leg Curl/Leg Extension and Glute Drive cover compound and isolation lower body training from selectorized stations built for heavy daily volume. A complete cable training ecosystem spans from the Adjustable Cable Crossover and Dual Adjustable Pulley through to the 4-Stack, 5-Stack, and 8-Stack Multi Station systems for facilities that need multiple concurrent training zones.

Every machine is built from heavy-duty commercial steel, finished in matte black, and backed by Dynasty's lifetime frame warranty. This is commercial-grade equipment at a price point that makes it accessible to every serious training environment.

Explore the Elite Series

Commercial Machines, Home Gym Prices

Commercially Engineered, Available to All

OUR COMMITMENT

Every machine that leaves Dynasty Fitness carries the same promise: it is built to the commercial standard that professional training environments demand, priced so that standard is no longer exclusive to them, and backed by the support and warranty coverage that a long-term training investment deserves.

We are committed to equipment that stands the test of time — and to making sure the people who train the hardest have access to the tools that match their effort.